牌号简介 About |
---|
出于库存控制目的,产品名称后面可以跟一个X。标记为FEP CJ 99和FEP CJ 99 X的产品是等效的,本文件中的所有信息都适用于这两者。典型应用电线电缆绝缘,小管道和注塑件。杜邦特氟隆FEP CJ 99是一种不含添加剂的四氟乙烯和六氟丙烯的熔融加工共聚物,符合ASTM D 2116 I型的要求。由于熔融流速在9 g/10 min范围内的独特组合和超过40000个循环的MIT弹性寿命,该树脂提供了有吸引力的加工速度和高性能。GH耐应力机架除了具有典型的聚四氟乙烯氟聚合物树脂的优良特性外,还具有非老化特性、化学惰性、特殊的电气特性、低可燃性、耐热性、韧性和柔韧性、低摩擦系数、不粘特性、可忽略的吸湿性。具有良好的耐候性。特氟隆FEP CJ 99透明度的提高也将使其具有更好的着色性。应力抗裂性是确定最终使用性能的重要因素。为了确定性能评估,需要对电线和电缆结构进行广泛的测试。众所周知,最全面的电线和电缆应力架电阻试验是军用规范MIL-W-22759(航空航天)和ISO 6722/LV112(汽车)中所述的芯轴缠绕试验。经验表明,基于ASTM D 2176,在树脂薄膜上进行的MIT耐折性或弯曲寿命试验与应力开裂性能有很好的相关性。具有较高的MIT弹性寿命的树脂,在应力开裂试验中表现更好。与大多数粘度相近的FEP树脂(MFR)相比,Teflon FEP CJ 99具有更高的抗应力开裂性能,并且比具有相同抗应力开裂性能(MIT)的FEP树脂具有更高的生产率。我们建议,对于涉及重复热循环和弯曲循环的应用,应始终对最终电缆进行特定测试。麻省理工学院的测试结果应被视为不同等级树脂比较性能的指南。 For inventory control purposes product name may be followed by an X. Products labeled FEP CJ 99 and FEP CJ 99 X are equivalent and all information in this document is applicable to both. Typical Application Wire and cable insulation, small tubing and injection molded parts. DuPont Teflon ® FEP CJ 99 is a melt-processible copolymer of tetrafluoroethylene and hexafluoropropylene without additives that meets the requirements of ASTM D 2116 type I. Thanks to the unique combination of a Melt Flow Rate in the range of 9 g/10 min and MIT flexlife above 40 000 cycles, this resin offers both attractive processing speeds and high stress-rack resistance in addition to the excellent characteristics typical of Teflon ® fluoropolymer resins, such as non-ageing characteristics, chemical inertness, exceptional electrical properties, low flammability, heat resistance, toughness and flexibility, low coefficient of friction, non-stick characteristics, negligible moisture absorption and excellent weather resistance. The increased transparency of Teflon ® FEP CJ 99 will also allow better colourability. Stress crack resistance is an important element in establishing end-use performance. Extensive testing of wire and cable constructions is required for definitive performance evaluation. Well-known and most comprehensive tests for stress rack resistance of wire and cable are mandrel wrap tests as described in the military specification MIL-W-22759 (aerospace) and ISO 6722/LV112 (automotive). Experience has shown that the MIT folding endurance or flex life test, based on ASTM D 2176, performed on a thin film of resin, gives a good correlation with stress crack resistance. Resins with a higher MIT flex life, perform better in the stress-crack resistance tests. Teflon ® FEP CJ 99 has a higher degree of stress crack resistance than most FEP resins with similar viscosity (MFR) and offers higher productivity than FEP resins with similar stress crack resistance (MIT). We recommend that for applications involving repeated thermal and flex cycling, specific tests on the final cable always should be undertaken. The MIT test results should be viewed as guide to comparative performance of the various grades of resin. |
产品描述 Product Description
厂家:美国科慕 Chemours
类别:FEP FEP
用途:电线电缆应用;绝缘材料;
加工条件:挤出 Extrusion
性能特点: 低吸湿性; 防火阻燃等级V-0; 成型周期快; 着色性好; 耐化学性; 耐高温; 电气性好; 食品接触; 低摩擦系数; 耐候抗UV; 抗应力开裂; 韧性好; Weather resistance is good,Good flexibility,Good Electrical Properties,Low coefficient of friction,Quick molding cycle,Food contact compliance,High Heat Resistance,Solvent resistance,Low moisture absorption,High ESCR,Good coloring,V-0
技术参数 Technical Data | |||
---|---|---|---|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
密度 Density |
|||
-- -- |
2.13 | g/cm³ | ASTM D792 |
-- -- |
2.13 | g/cm³ | ISO 1183 |
熔体质量流动速率 Melt Flow Rate |
|||
372℃,5.0kg 372℃,5.0kg |
9.0 | g/10min | ASTM D2116 |
372℃,5.0kg 372℃,5.0kg |
9.0 | g/10min | ISO 12086 |
吸水率 Water absorption rate |
|||
24hr 24hr |
< 0.010 | % | ASTM D570 |
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
邵氏硬度 Shore hardness |
|||
邵氏 D Shaw's D |
ISO 868 | ||
邵氏 D Shaw's D |
ASTM D2240 | ||
拉伸强度 tensile strength |
|||
屈服,23℃ Yield, 23 ℃ |
MPa | ISO 12086 | |
屈服,23℃ Yield, 23 ℃ |
MPa | ASTM D638 | |
拉伸应变 Tensile strain |
|||
断裂,23℃ Fracture, 23 ℃ |
% | ISO 12086 | |
断裂,23℃ Fracture, 23 ℃ |
% | ASTM D638 | |
冲击性能 IMPACT |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
悬臂梁缺口冲击强度 Impact strength of cantilever beam notch |
|||
23℃ 23℃ |
ASTM D256 | ||
23℃ 23℃ |
ISO 180 | ||
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
连续使用温度 Continuous use temperature 2 |
℃ | ||
熔融温度 Melting temperature 5 |
℃ | ||
电气性能 Electrical performance |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
介电强度 Dielectric strength 4 |
|||
0.25 mm 0.25 mm |
kV/mm | IEC 60243-1 | |
0.25 mm 0.25 mm 4 |
kV/mm | ASTM D149 | |
介电常数 Dielectric constant |
ASTM D150 | ||
1 kHz 1 kHz |
ASTM D150 | ||
1.00 GHz 1.00 GHz |
ASTM D150 | ||
相对电容率 Relative permittivity |
IEC 60250 | ||
1 kHz 1 kHz |
IEC 60250 | ||
1.00 GHz 1.00 GHz |
IEC 60250 | ||
耗散因数 Dissipation factor |
ASTM D150 | ||
1 kHz 1 kHz |
ASTM D150 | ||
1 GHz 1 GHz |
ASTM D150 | ||
耗散因数 Dissipation factor |
IEC 60250 | ||
1 kHz 1 kHz |
IEC 60250 | ||
1 GHz 1 GHz |
IEC 60250 | ||
阻燃性能 FLAME CHARACTERISTICS |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
阻燃等级 Flame retardant level 5 |
UL 94 | ||
极限氧指数 Extreme oxygen index |
% | ASTM D2863 | |
极限氧指数 Extreme oxygen index |
% | ISO 4589-2 | |
补充信息 Supplementary information |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
Critical Shear Rate(372℃) Critical Shear Rate(372℃) |
sec^-1 | Internal Method | |
Guide DDR Range(for cable extrusion) Guide DDR Range(for cable extrusion) |
|||
MIT耐折强度(film,200.0 µm) MIT flexural strength (film, 200.0 µ m) |
Cycles | ASTM D2176 |
备注 |
---|
1 一般属性:这些不能被视为规格。 |
2 The continuous service temperature is based on accelerated heat-aging tests, and represents the temperature at which tensile strength and ultimate elongation retains 50% of the original values, after 20 000 h thermal aging When considering the use of Teflon ® FEP at elevated temperatures especially in combination with mechanical, electrical or chemical exposure, preliminary testing should be done to verify suitability. |
3 ASTM D4591 / D3418 |
4 方法A(短时间) |
5 - These results are based on laboratory tests, under controlled conditions, and do not reflect performance under actual fire conditions. - Current rating is a typical theoretical value |
【新闻资讯】查看全部
墨西哥湾海岸成长公司两装置机械竣工
2021-08-08 搜料网资讯: 近日,埃克森美孚和沙特基础工业公司(SABIC)的合资企业,墨西哥湾海岸成长公司宣布,该公司在得克萨斯州科珀斯克里斯蒂附近新建石化厂的聚乙烯和乙二醇设施已实现机 |
墨西哥湾海岸成长公司两装置机械竣工 搜料网资讯:近日,埃克森美孚和沙特基础工业公司(SABIC)的合资企业,墨西哥湾海岸成长公司宣布,该公司在得克萨斯州科珀斯克里斯蒂附近新建石化厂的聚乙烯和乙二醇设施已实现机械竣工。该公司预计,两装置将提前在2021年第四季度投入运营。聚乙烯综合产能130万吨/年,乙二醇产能为110万吨/年。该综合厂还将包括一套180万吨/年的乙烷裂解装置。合资公司表示,该项目预计将控制在预算内,成本将比美国墨西哥湾沿岸的类似项目低约25%。 埃克森美孚化学公司总裁凯伦·麦基表示:“墨西哥湾海岸成长公司是我们发展计划的关键一环,旨在满足人们对我们高价值高性能产品日益增长的需求。” |
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任,并强烈建议在最终选择材料前,就数据值与材料供应商进行验证。 |
第三方认证:
抱歉!该牌号暂无认证数据。
价格走势图
开始时间:
结束时间:
材料厂家:
【牌号齐全,内容全面】
全网共2500+项牌号+上游原料单体+原油价格,最长可追溯近20年价格行情
【精准,及时,权威!】
专业团队挖掘行情信息,第一时间发布行情
抱歉!该牌号暂无认证数据。
免责声明:参考价格是搜料网根据网络大数据拟合分析的结果,仅供参考。实际成交价取决但不限于以下因素:下单时间,付款方式,交货方式,数量,税费,色号,产地,项目信息。
抱歉!暂无数据。
抱歉!暂无数据。